Technical Questions – FAQ’s
Last updated
463 posts · page 6 of 31
A286 Cryogenic Usage
Q: I have an deep space application that may experience varying temperatures from extreme highs as well as cryogenic. I’ve been told about A286, but can it be used at cryogenic temperatures too? A: Yes, A286 can be used at cryogenic temperatures down to -320 where it will remain ductile…
Continue readingMechanical Properties of A286
Q: What are the mechanical properties of A286 Bolts?A: Below are the general properties of A286 bolts in terms of high temperature usage and strength. This can change though depending on the AMS or ASTM specifications. - A286 tensile strength 120ksi, 160ksi (cold worked) - A286 yield strength 85 ksi,…
Continue readingRelationship Between Tensile Strength and Hardness
Q: How does the tensile strength of a metal compare to its hardness? A: Ok there are a few questions here so let’s start with the strength and hardness comparison first. Tensile strength by definition is the amount of stress a material can handle before it will fail – or…
Continue readingHow to Prevent Thread Galling
Q: I think my bolts are galling to the heat exchanger I’m working with because now they won’t budge at all. Guessing I will have to break them to get them out. I don’t want to have this keep happening – so is there any way to prevent this from…
Continue readingMaterials Prone to Thread Galling
Q: I’ve had trouble with galling in the past and seem to be wasting a lot of bolts, due to this. I’ thinking maybe that I’m using the wrong material – so are there specific materials better than others to help prevent galling? A: Though galling can happen with almost…
Continue readingWhat is Thread Galling?
Q: I’ve heard of thread galling but am not exactly sure what it is. Can you explain? A: Galling happens when a bolt is over-tightened and the threads seize together creating what we call a “cold weld”. The friction from fastening actually causes the threads to heat up and the…
Continue readingDifference between Galvanic Corrosion & Galling
Q: Are galvanic corrosion and galling the same? A: Galvanic corrosion and galling are actually very different. One causes accelerated corrosion while the other cause the threads to seize. Galvanic corrosion is when two dissimilar metals are brought in contact with a solution or moisture – most commonly, salt water.…
Continue readingFinishes to Prevent Bolt Thread Galling
Q: Do you have any finishes that you can recommend to add to the studs/nuts to prevent galling? A: Regarding galling there are a few things that could be done depending on your application’s needs. 1) The easiest and cheapest solution is to use an anti-seizing lubricant. We sell one…
Continue readingNon-Conductive Screws
Q: I’m involved in is currently looking at your non-conductive fasteners to isolate an SMA Connector. But have several questions for finding the right solution regarding torque, preload heating and cooling, and locking features. A: Thanks for all the questions and interest. I will answer all your questions: How is…
Continue readingWhat Is the Max Length of a Ceramic Fastener
Q: Hi, I’m search to get a 1/4″-20 x 3ft long alumina ceramic rod. Is this something you can make? A: For Extreme Bolt & Fastener, 3″ long is the max length we can produce a ceramic bolt, rod or other fastener. As you may know ceramics are brittle, but…
Continue readingMaximum Temperature for Duplex /1.4462 Screws in Saltwater
Q: At what temperature is it safe to use 1.4462 Duplex Stainless Steel Screws in seawater? A: 1.4462 Duplex stainless steel comes under several material and trade names including, 2205, UNS S32205, UNS S31803, F51, AISI 318 LN. It is normally safe to use duplex stainless bolting in brine /…
Continue readingMax Usable Temp of A286 (1.4980) Bolts
Q: I am designing an engine unit and am considering using 1.4980 stud bolts and nuts at elevated temperature. What is the maximum working temperature for stud bolts made of 1.4980 (A286)? A: A286/Alloy 660 or 1.4980 fasteners are made of a stainless steel alloy which contains iron, nickel, and…
Continue readingInconel 718 Per SAE AS7466 Vs SAE AS7467
Q: What is the difference between bolting to SAE AS7466 and SAE AS7467? A: Both SAE AS7466 and SAE AS7467 describe bolts and screws made from Inconel 718 (UNS N07718) material equivalent to the European 2.4668 material norm. The main difference between these two specifications is the testing requirements. The…
Continue readingASTM A1014 Compared to SAE AS7467
Q: What is the difference between screws made to ASTM A1014 and SAE AS7467? A: When it comes to the material characteristics there is not much difference in these specifications. Both standards describe bolts and screws made from Inconel 718 (UNS N07718) material equivalent to the European 2.4668 material norm.…
Continue readingASTM A1014 versus AMS 5663
Q: What is the difference between a screw made to ASTM A1014 and AMS 5663? A: ASTM A1014 is standard specification for precipitation hardened bolts in Inconel 718 (UNS N07718) for high hemperature service by ASTM International. In contrast AMS 5663 is the material standard from another standards agency: SAE…
Continue reading
