Technical Questions – FAQ’s
Last updated
463 posts · page 5 of 31
Fast Delivery for 1300C and Low Load Strength
Q: I’m looking to purchase some ¼-20 bolts/nuts/washers that will be suitable to fasten metal plate together at 1,300C. The fasteners need to last at least 4 minutes at this temperature but preferably longer. The load on the bolts will be very low. A: I think there are a couple…
Continue readingAluminum 7075 Compared to Titanium
Q: How does Aluminum 7075 compare to titanium grade 5? A: Aluminum 7075 can be tempered to many different strengths. The strongest being T6 which not only offers the highest strength. The primary drawback being that it also has low fracture toughness. Aluminum 7075-T6 bolts offer more strength than grade…
Continue readingAluminum 7075 for Lightweight Strength
Q: Why is Aluminum 7075 often used for aircraft? A: There are many grades of aluminum bolts but those categorized under grade 7075 are specifically used for aerospace and other high stress structural applications that require a combination of strength and extreme light weight. Grade 7075 can be tempered to…
Continue readingInconel 718 per AMS 5962
Q: What is the difference between “standard” Inconel 718 and Inconel 718 per AMS 5962 A: While nothing about Inconel 718 is standard, however the most popular variety of Inconel 718 bolts is per ASTM B637. For this version of Inconel 718, the bolts are age hardened to have a…
Continue readingMonel 400 Bolts per ASTM B164
Q: What does the spec ASTM B164 apply to and can you produce hex heads per this spec? I believe it is for Monel bolts?A: Monel bolts per ASTM B164 applies to both Monel 400 and Monel grade 405. This specification standardizes the different processing techniques for each of these…
Continue readingPEEK: Non-Conductive Bolts for up to 500F
Q: We are looking to find an electrically non-conductive bolt that would also work at temperatures up to 500 F max. They will be used for an electrically live part isolation kit. Anything that will fit the bill? A: Without any understanding of your strength requirements, and focusing solely on…
Continue readingInconel 718 Bolts Per ASTM B637
Q: What does it mean for Inconel bolts to be produced per ASTM B637.A: The specification ASTM B637 is a raw material specification for both hot- and cold-worked precipitation- hardened nickel alloy rod, bar, forgings, and forging stock for high-temperature service. Inconel 718 bolts are one of several age hardened…
Continue readingMIL-DTL-25027 for Lock Nuts
Q: Can you provide me the dimension specs of an MIL-DTL-25027 5/8″-11 Monel 400 nut?A: MIL-DTL-25027 (superseded by spec NASM25027 ) focuses on the performance criteria of the locking mechanism of the nut. This spec isn’t for the dimensions/configuration of the nut.
Continue readingPEEK Screws for Shock and Vibration
Q: I need a flat head screw that is both non-Conductive Fastener and can survive shock and vibration. Any ideas?A: Polymers and ceramics are the only options for non-conductive screws. As ceramics are brittle, they would non withstand shock and vibration. In terms of polymers, PEEK is the go-to option…
Continue readingStrong, Non-conductive, Impact Resistant Screws
Q: We are looking for screws to hold down electronic circuit boards. Unfortunately the mounting provisions need to be electrically isolated from the mounts. In addition, we need strength, non-conductivity, and impact resistance, even at cold temperatures (-40C). A: A great material to consider would be PEEK screws or PEEK…
Continue readingGalling Issues with Inconel and Hastelloy
Q: How do Alloy 625 and Hastelloy C276 bolts work together as far as galling goes?A: Inconel 625 bolts and Hastelloy bolts should work well together. They have slightly different chemistries, which helps minimize galling. In addition, Inconel is a bit harder than Hastelloy, which also helps. As long as…
Continue readingAre 304 stainless steel and 18-8 stainless steel the same material?
Q: Am I correct in my understanding that 304SS (UNS S30400) can be sold as “18-8” hardware – but that not all 18-8 hardware is necessarily (UNS S30400)?A: 304 stainless steel fits into a general category of stainless steel that is referred to as “18-8”. However, if you buy 18-8…
Continue readingNAS1352 and NAS1352
Q: What is the difference between NAS1351 and NAS1352? Aren’t they both socket head cap screws?A: Yes, both NAS1351 and NAS1352 are both socket head cap screws. The primary difference is the threads. NAS1351 pertains to socket head cap screws with a coarse thread pitch, whereas NAS1352 applies to only…
Continue readingFlat Head Socket Cap Screw Angles
Q: Can you make a 100 deg flat head, with a hex socket driver?A: Yes this screw can be produced but there are some significant trade-offs that need to be realized.Though a hex socket driver is a typical driver in an 82 deg flat head screw, in this instance for…
Continue readingA286 Bolts per AMS 5737 Compared to AMS 5732
Q: What is the difference between A286 per AMS 5737 and AMS 5732?Q: What is the difference between A286 per AMS 5737 and AMS 5732? A: A286 is an age hardened material. These AMS – aerospace standards – pertain to how the A286 material is solution treated and hardened: •…
Continue reading
