Technical Questions – FAQ’s
Last updated
463 posts · page 12 of 31
PEEK for Low Thermal Conductivity & Strength
Q: I’m currently cruising the internet looking for the best way to support a ceiling via suspension from structural steel. We’re building a freezer, and I don’t want thermal bridging from the inside of the freezer up to the structural steel, so a metal rod is pretty much out of…
Continue reading310 Stainless Steel bolts compared to Inconel 600 bolts
Q: I have a high temperature application that requires bolts that can withstand around 1900F. There is almost no corrosive contamination – strictly heat and oxidation resistance are required. I see both Inconel 600 and 310 stainless can be used at this temperature – what is the difference and which…
Continue readingHex Head Bolt Compared to Hex Head Cap Screw
Q: I’m confused about the difference between a hex head bolt and hex cap screw? Is there a difference? A: Yes these are two different types of fasteners. A hex head bolt is just that: a bolt with a head head. It is typically used when mechanical properties are more…
Continue readingAllen, Hex, and Socket Drivers
Q: What is the difference between an allen, hex and socket driver? A: All these drivers are the same. They can be offered in a socket head cap screw (hence the term socket), pan head and flat head. An allen/hex/socket drive offers a more secure connection than say a flat…
Continue readingTitanium Hose Clamp for Chlorine Water Vapor
Q: I’m looking for a clamp for a drinking water tank vent screen. We work with many tanks but this tank apparently has a higher chlorine residual so the 304SS worm drive clamps don’t last long. The clamp that we fabricated was a little too stiff so there were gaps…
Continue reading17-4PH Bolts per ASTM A564, Type 630
Q: I have a question on 17-4PH H1150, do you know what the tolerance on the material strength is? Ie +/- 10% ? A: For a 17-4 H1150 bolt, we would use the ASTM A564, Type 630 spec to define the strength as 115 KSI Min Tensile, 105 KSI Min…
Continue readingInconel 600 Bolts Compared to Ceramics in High Temperatures
Q: I have a high temperature application that runs at about 1900- 2000F. Would a ceramic bolt be a good idea. I need to have some strength and Alumina says it offers 75 ksi UTS? Will that work? A: Ceramics are not often a good idea when their are any…
Continue readingHastelloy C276 vs Inconel 625 Bolts
Q: What’s the difference between Hastelloy C276 and Inconel 625?A:C276 bolts have an edge in corrosion resistance on Inconel 625 bolts. Typically Hastelloy bolts are the go-to in many harsh chemical environments and offer improved resistance most notably in hydrochloric acid. Hastelloy is also renowned for their resistance to sour…
Continue readingNylon vs All Metal Lock Nuts
Q: What is the difference between a Duplex nylon insert and all-metal lock nut? I’ll be using this in an offshore marine application for salt air resistance and strength. A: The main things to consider between an all metal and nylon insert lock nut is the temperature and the corrosive…
Continue readingNAS, and MS parts – What do these mean?
Q: My customer is requesting NAS and MS part numbers. What do they stand for and why are they important? A: NAS parts are National Aerospace Standards. NAS parts are best known for their precision and high strength. They come in all types of screws, nuts, rivets, rod end bearings,…
Continue readingAlternative Material to Aluminum 7075
Q: Can you suggest a different material with similar strength-to-weight ratio as the 7075, that can be produced with a diameter M3-0.5? A: Since an M3 bolt is too small to be produced from Aluminum 7075, I would suggest either grade 2 titanium bolts or grade 5 titanium bolts. For…
Continue readingInconel Bolts: Preventing Galling/Seize & Over-Torque
Q: I need an Inconel 625 screw for a high temperature environment with trace corrosives. I’d need torx head bolt style. How many times can I tighten and loosen this type of bolt before I need to replace it? A: You should be able to get hundreds or even thousands…
Continue readingDowel Pin Tolerances
Q: I am looking to purchase dowel pins but are there standard tolerances? A: Yes, tolerances for standard inch size dowel pins would be per the ANSI B18. 8.2 spec. They have a diameter tolerance of -0.00 / +0.0002 and length tolerance of +/-0.010. If different tolerances are required then…
Continue readingA286 Bolts and Alloy 330 Bolts for Cyclic High Temperatures
Q: I need some suggestions on bolting for an application that is running at 610 degree C in a thermal cycling environment (Room temperature to 610 deg C). Is A286 a good fit?A: This will depend a bit on the loads you are dealing with, but one of the best…
Continue readingPEEK Bolts for Non-Conductivity / Galvanic Corrosion
Q: We are attaching steel to aluminum in a drainage pond application, and need to prevent electrolysis. The aluminum materials are degrading prematurely. Is there a non-conductive bolt that would work for this situation? A: Your best bet is if you can use a polymer bolt like PEEK. PEEK bolts…
Continue reading
