Skip to main content
Extreme Bolt & Fastener
Quote

Technical Questions – FAQ’s

Last updated

463 posts · page 19 of 31

  • Alloy 330 vs 310 Stainless for Thermal Cycling

    Q: Can you tell me the difference between alloy 330 and 310 stainless fasteners? I’d like a more economic alternative to the 330 but didn’t know if 310 stainless could be used instead. I have extreme cyclic conditions running to about 2000F? A: If cyclic conditions are a concern you…

    Continue reading
  • Titanium Screws for Bleach Corrosion Resistance

    Q: We are using a bleach solution as part of a medical device application and seeing some rust/corrosion? Any ideas on a fastener material that will not corrode in bleach? Chemicals used are: 5.25% Sodium hypochlorite (or 10% bleach), 70% Isopropyl alcohol and Ammonium chloride A: You might want to…

    Continue reading
  • PEEK for High Strength Electrical Insulation

    Q: We are looking for high shear strength non-conductive flat head screws being used for electrical insulation. The screws need to have a high shear strength quality as other plastics screws we have tried have broken. Do you have a material you can recommend? A: With regards to a polymer…

    Continue reading
  • Zirconium Fasteners for HCl Corrosion

    Q: Can I use zirconium bolts in boiling HCl. Concentration would be about 5%? A: Yes, zirconium fasteners work well in hydrochloric acid but may be a bit overkill at that relatively low concentration but depends on the temperature and other media it may be exposed to. Zirconium screws do…

    Continue reading
  • 254 SMO vs. Alloy 20 or AL6XN in Sulfuric Acid

    Q: How does 254 SMO compare with Alloy 20 and AL6XN? Can it handle sulfuric acid?A: To answer your first question, I’ve ranked each of these specialty alloys in terms of their general corrosion resistance to sulfuric acid:1. Alloy 20 Most2. AL6XN Moderate3. 254 SMO LeastOverall these alloys all perform…

    Continue reading
  • PVDF Screws for Sulfuric Acid & Strength

    Q: I’m looking for a polymer that can be exposed to low concentration of sulfuric acid. Which polymer do you recommend? I tried PTFE but they don’t seem to be as strong as I need.A: PTFE and PFA fasteners offer the highest polymer corrosion resistance but the trade-off is lower…

    Continue reading
  • Duplex Steel Bolts for Brackish Water

    Q: I’m looking for a material that can service a brackish water environment with high strength around 100ksi, would SMO 254 work for me?A: In terms of the corrosion resistance, yes, but for strength you are right on the edge of the capabilities for 254 SMO fasteners. 254 SMO bolts…

    Continue reading
  • Moly Bolts Ideal for High Temperature Vacuum

    Q: Are Nimonic bolts a good choice for a high temperature vacuum environment?A: That depends. Typically for extreme temperatures in a vacuum we recommend Molybdenum fasteners. Moly bolts have an extremely high melting point and can be used at much higher temperatures – close to 2900F – ONLY when not…

    Continue reading
  • Hastelloy Bolts for Nitric Acid Corrosion

    Q: Which material would be better suited for a nitric acid environment (Hastelloy C276 or Inconel)? The screws would not be submersed in the acid, but in a room where the screws would be around the fumes. A: For nitric acid fumes Hastelloy C276 bolts would be the go-to material…

    Continue reading
  • PEEK Polymer Screws for Sterilization Processes

    Q: I need a fastener that can withstand frequent sterilization processes at temps to around 400F. I would prefer a polymer if possible. Also the process is pharma related, so the screws would need to be non leaching and may be exposed to low concentrations of chemicals. Any ideas? A:…

    Continue reading
  • Titanium Grade 2 Fasteners for Chlorides/Moderate Strength

    Q: Hello I am researching titanium and C276 hardware for a submerged application in a high chloride (20,000 mg/L) elevated temperature environment (125F). Corrosion resistance is more important than shear or tensile strength in this application. A: Titanium screws should be a good choice for your application especially Grade 2…

    Continue reading
  • Lightweight Nut Similar Strength to Class 10 Steel

    Q: I’m looking for a nut in a large metric size. I know I can’t get it made in this large a size for class 10 steel so I’m hoping you can recommend a material that can be made to an M16 with similar strength. A: If you are looking…

    Continue reading
  • Super Duplex Bolts for Greater Strength over 400 Stainless

    Q: Currently I’m using screws made of 400 series stainless steel for use in factory machinery that is moving in a circular path creating a centrifugal force. Our existing bolts are breaking and we’re looking for a bolt with a more rigid type of material that will not break or…

    Continue reading
  • Strong, High Temperature Fastener for Gas Turbines

    Q: I’m in need of hex head bolts for a gas turbine hot section application. These bolts would need good strength and min. temperature tolerance of 1000 degF. Any suggestions? A: A286 bolts are an option, but would be on the lower end of these materials in terms of temperature…

    Continue reading
  • Monel Better than Nickel 200 for HF Corrosion

    Q: Will Nickel 200 bolts be a good choice for hydrofluoric acid? A: For aqueous HF, Nickel 200 fastenersoffer limited protection. If application requires a metal then you may want to consider Monel 400. Monel 400 bolts are the most resistant option for hydrofluoric acid in all concentrations up to…

    Continue reading

Questions?

Our material experts are ready to help guide you through your specific application.