Skip to main content
Extreme Bolt & Fastener
Quote

Technical Questions – FAQ’s

Last updated

463 posts · page 22 of 31

  • Titanium Anchor Bolts for Marine Concrete Fastening

    Q: I have a need for a marine resistant fastener that I can use to fasten equipment to concrete. Is there a bolt you can recommend? A: For concrete fastening one of the best solutions is a wedge anchor bolt. This style of bolt features an expansion mechanism which expands…

    Continue reading
  • Wedge Anchors for Concrete Fastening

    Q: Can I use a wedge anchor to attach a piece of equipment to metal? I need a high strength fastener. A: No. Wedge anchors are used to strictly for fastening into concrete. The anchor is actually an expansion mechanism which fans out and locks the bolt into concrete as…

    Continue reading
  • Super Duplex Bolts Ideal for Strength & Seaspray

    Q: I need a large quantity of fasteners that can offer about 100ksi of tensile strength and provide me resistance to seaspray and salt air. Is titanium a good choice? A: Titanium grade 5 bolts will meet both these requirements, but will probably be overkill in your situation. For this…

    Continue reading
  • Bolts to Meet NACE Oil & Gas Specs

    Q: We’re in need of bolts for an oil & gas refinery. How can I be sure you your materials meet technical requirements.A: We can provide fasteners that meet NACE MR0175 and NACE MR0103specific requirements for different metallic materials. When requesting a quote, please ask for all necessary specifications so…

    Continue reading
  • Hastelloy and Nitric Acid

    Q: Can I use Hastelloy C276 bolts for protection from Nitric Acid?A: Typically this is not recommended. Though C276 boltsare highly corrosion resistant to many acids, it is not very resistant to strong oxidizers like nitric acid. Materials with higher chromium content like Incoloyand possibly Hastelloy C22tend to be more…

    Continue reading
  • Tantalum Coating for High Temperature

    Q: I’m interested in TZM or Tantalum fasteners and was also wondering if there was an option to have the fasteners coated to increase the use temperature in air? A: There really is not a coating that could be used for tantalum and molybdenum screws to increase their life in…

    Continue reading
  • Nickel 200 Bolts for Sodium Hydroxide Corrosion

    Q: We’re using sodium hydroxide as a water treatment chemical to raise the pH of water but are experiencing corrosion. Is there a material that can handle this?A: Typically for caustic soda (sodium hydroxide) corrosion, you might want to consider Nickel 200 bolts. Nickel 200 is best known for its…

    Continue reading
  • 17-4PH for High Strength Applications

    Q: Looking at options to increase the tensile strength for a socket head cap screw. We are currently using grade 8. Would Waspaloy be a good option? A: If you are looking for a fastener with higher strength than Grade 8 Alloy Steel (150 KSI Tensile, 130 KSI Yield), and…

    Continue reading
  • A286 Bolts for High Temperature Annealing Oven

    Q: I have require fasteners for use in an annealing oven for aa centrifugal fan (@1725 RPM) attached to a shaft with a through bolt and nut (shaft and fan are both SST). The environment is 1275 degrees F at atmospheric pressure and runs continuously 5 days a week I…

    Continue reading
  • Inconel 625 Studs for Temperatures of 1650°F

    Q: What stud and nut material should I use with a ANSI 600 Alloy 800 HT pipe class max temperature 1650°F. A: Given that you are at a high temperature and pressure I would recommend going with an Inconel 625 stud. This will provide the best combination of high temperature…

    Continue reading
  • Large Diameter Bolt Torque Specifications

    Q: Are you able to provide the assembly torque number for titanium M42 diameter bolts? A: The torque required for large bolts like this can vary GREATLY depending on the conditions, lubrication, surface roughness, dirt, etc. The required torque can vary by as much as +/-50%. However with that in…

    Continue reading
  • PEEK Screws for Non-Conductive High Impact Application

    Q: Looking to change to a non-conductive material for use in a high impact application. Would Alumina or Zirconia ceramic fasteners be a good fit? A: We could certainly quote you some ceramic hardware, however ceramics may not be the best non-conductive choice for a high impact environment. Ceramic fastenersare…

    Continue reading
  • Non conductive, cryogenic fasteners: PEEK & PTFE

    Q: I have a need for a fastener for cyrogenic Helium (3.5K) application. Ideally, the fastener would be non conductive (electrically). Are any of the non conductive options you have listed good for cryo use? A: You might want to consider PTFE of PEEK fasteners. These are polymers that will…

    Continue reading
  • Inconel for High Strength Sour Gas Applications

    I am looking for the best available material solution for Oil&Gas industry with occasionally presence of H2S. For now we are using A286 but I am not sure about its H2S resistance. What kind of material you can recommend that is comparable to A286 and is H2S rated? When dealing…

    Continue reading
  • Tensile Strength Options for Inconel 718 Bolts

    Q: Im looking for Inconel 718 bolts but I need a bit more strength than what is typically offered as a min of 185ksi Ultimate Tensile. Is it possible to make Inconel 718 stronger than that?A: Yes…Actually Inconel 718 bolts are available in a few different flavors. The most common…

    Continue reading

Questions?

Our material experts are ready to help guide you through your specific application.