Skip to main content
Extreme Bolt & Fastener
Quote

Technical Questions – FAQ’s

Last updated

463 posts · page 24 of 31

  • Non-Conductive Fasteners – Polymers or Ceramics?

    Q: I need a bolt that can handle high temperatures and be an electric insulator? What can I use? A: That depends on what you mean by high temperature and what other issues you have like the strength requirements. If you are talking about temperatures under 500F, then you may…

    Continue reading
  • Non-Electrically Conductive Fasteners – Polymers or Ceramics?

    Q: I’m looking for a socket head cap screw that is 5/8″-11 x 5.5 inches in length. Need the material to be non-conductive and was thinking Ceramic Zirconia? Would that work?A: Ceramics like Zirconia screws are in fact an excellent insulator from electrical current. However zirconia ceramic fasteners are very…

    Continue reading
  • 17-4 Corrosion Resistance to Sulfuric Acid & Inconel

    Q: Are there any materials I can use with the strength of 17-4PH in the H1150 heat treat, but with better corrosion resistant properties. I have low levels of sulfuric acid and chlorides that seem to be attacking the 17-4 steel.A: The best choice for both extreme strength and corrosion…

    Continue reading
  • Inconel bolts vs Alloy 330 at high temps

    Q: I’m designing a furnace vent system for a continuous service high heat appliance (NFPA 211). The maximum furnace working temperature is 2100 deg F; design temperature is 2190 deg F. Will Alloy 330 or 310 SS bolts and nuts work for me? A: You are at the absolute limit…

    Continue reading
  • PEEK vs Torlon Fasteners for Non-Conductivity & Salt Water

    Q: I’m looking for a polymer washer that can be used as a dielectric break between aluminum and titanium. It will also be exposed to salt water. Is torlon a good choice? A: Torlon washers will work in this situation, but there are probably more cost efficient solution for this…

    Continue reading
  • Titanium Bolts Trump Monel for Intense Chloride Applications

    Q: Since Monel is resistant to NaCl does that mean it can handle a strong chloride situation? A: Monel is resistant to chlorides but, for strong chlorides your best bet is to use Titanium screws. Titanium fasteners are almost inert to all chlorine and chloride environments due to the fact…

    Continue reading
  • When NOT to Use Zirconium Bolts in Nitric Acid

    Q: I’ve been using zirconium to handle a nitric acid solution but am still experiencing corrosion? I’m not sure why or if there is a better option? A: Zirconium bolts offer some of the best corrosion resistance to nitric acid as well as sulfuric acid and hydrochloric acid, even at…

    Continue reading
  • Inconel vs 310 Stainless Steel Bolts

    Q: I have a high temperature application that can reach close to 1800F that requires not just corrosion resistance from low levels of acid and salt contamination, but I also need good strength. Would Alloy 310 bolts work?A: Alloy 310 bolts could be a possibility, depending on the strength you…

    Continue reading
  • PVDF Polymer Screws for High Strength Acid Resistance

    Q: I have a laboratory applications that uses about 25% sulfuric acid at room temperature to 100F. I’d like to use a polymer rather than a metal if possible. I tried PTFE screws because I thought they were corrosion resistant, but they need to be replaced often because they can’t…

    Continue reading
  • Titanium Screws and Chlorides

    Q: I’m dealing with a moderate chloride environment but my temperature can sometimes reach 450F. I’ve tried titanium bolts but am having some corrosion issues. Is there another material I can use? A: There are several potential choices but as the temperature increases the corrosion rate and aggressive nature of…

    Continue reading
  • Titanium Bolts for Reverse Osmosis Saltwater Corrosion

    Q: I’m working in a reverse osmosis facility that purifies seawater for drinking water. We are experiencing some corrosion in some of our valve attachments which I’m assuming is from the salt water. Any recommendations on a fastener that won’t corrode in these conditions? A: Your best bet would be…

    Continue reading
  • Inconel Bolt Fastening to Titanium in High Temperature

    Q: I have an application in which I require a 1/2in-13 Hex bolt that will be in an inert gaseous environment at 500C. The bolt will be fastened to a Titanium Grade 5 nut. What material bolt would work best? A: I would suggest either Inconel 625 or Inconel 718…

    Continue reading
  • Tantalum Bolts vs Polymer Bolts for HCl

    Q: We have on application in one HCL tank and we are using hastelloy bolts but they are not efficient. So I ask the quotation for material tantalum in metals or other material like PEEK, please advise what is the better solution. A: It depends on the temperature of the…

    Continue reading
  • 17-4PH Bolts Galling Solutions

    Q: We are a manufacturer seeking a fastener for an air cooled engine’s head bolt replacement project. The fastener would be used to hold a aluminum cylinder head. We would like to use 17-4PH but are concerned about galling?A: As you would be using two different materials, the 17-4PH and…

    Continue reading
  • Brittle Ceramic Screws vs Molybdenum in Vacuum Furnaces

    Q: We are using ceramic screws in one of vacuum furnaces, they’re breaking due to thermal stresses. There is lots of thermal cycling. Are their any less brittle materials we can use? The environment is low pressure with a max temperature of 1050C. Gases used in the system include: argon,…

    Continue reading

Questions?

Our material experts are ready to help guide you through your specific application.