Skip to main content
Extreme Bolt & Fastener
Quote

Advanced Ceramics

Last updated

Advanced ceramic fasteners in alumina and zirconia

Need help choosing a material?

Extreme Bolt & Fastener offers the highest performing advanced ceramic fasteners available to industry in the form alumina and zirconia materials. Below are numerous guides to help you compare our ceramics and their unique properties. Feel free to contact our materials experts for additional guidance and support in choosing the best ceramic fasteners for your challenging application.

Advanced Ceramics

Resources & Guides


Material Property Comparison

CERAMIC PROPERTIES
PropertyASTM or UL TestAluminaZirconia
PHYSICAL
Density (lb/in³)
(g/cm³)
D7920.141
(3.89)
0.220
(6.1)
Water Absorption, 24 hrs (%)D57000
MECHANICAL
Strength/Weight RatioTensile Strength / Density (g/cc)770012300
Tensile Strength (psi)D63830,00075,000
Tensile Modulus (psi)D63843,500,00030,000,000
Tensile Elongation at Break (%)D6380-
Flexural Strength (psi)D79055,000100,000
Flexural Modulus (psi)D79054,000,000-
Hardness, Rockwell, R/M ScaleD785A88A80
IZOD Impact Notched (ft-lb/in)D256--
THERMAL
Coefficient of Linear Thermal Expansion (x 10-5 in./in./°F)D6960.50.6
Heat Deflection Temp (°F / °C) at 264 psiD648nonenone
Melting Temp (°F / °C)D3418--
Max Operating Temp (°F / °C)-3000/16504350/2400
Thermal Conductivity (BTU-in/ft²-hr-°F)C177242.015.0
Flammability RatingUL94non-flammablenon-flammable
ELECTRICAL
Dielectric Strength (V/mil) short time, 1/8" thickD14923050
Dielectric Constant at 1 MHzD1501028
Dissipation Factor at 1 MHzD1500-
Volume Resistivity (ohm-cm) at 50% RHD2571x1014> 1012
APPROVALS
ApprovalFDAYES-
ApprovalUSDANO-
ApprovalNSFNO-
Approval3A DAIRYNO-
ApprovalUSP CLASS VIMedical Grades Available-

Usable Temperature Limits

USABLE TEMPERATURE LIMIT GUIDEActual Limits Are Application Specific.
Consult An Expert.
MaterialsUsabel Temp Limit
(°F)
Usable Temp Limit
(°C)
Advance Ceramics
Alumina Ceramic30001650
Zirconia Ceramic (YSZ)43502400

Mechanical Properties

CERAMIC STRENGTH COMPARISON@ Room Temperature
MaterialUltimate Tensile
(ksi)
Yield Strength
(ksi)
Alumina30-
Ziconia (YSZ)75-

Advanced Ceramics - Frequently Asked Questions

Answers from our engineers, drawn from the Advanced Ceramics technical questions we're asked most.

I have a high temperature application that runs at about 1900- 2000F. Would a ceramic bolt be a good idea. I need to have some strength and Alumina says it offers 75 ksi UTS? Will that work?

Ceramics are not often a good idea when their are any strength requirements. They are strictly used for applications that soly require extreme temperature resistance of over 2000F in a non-vacuum environment. Though they do offer “strength” in terms of tensile strength, they offer no yield strength; and can be brittle and break. In this case, I would recommend you try Inconel 600 bolts. They have a tensile strength of 94 ksi and a yield strength of 37 ksi. In addition, these Inconel bolts‘ high temperature resistance fits perfectly into your necessary range with a max usable temperature of 2000F.

How do ceramic alumina screws compare to steel screws as far as strength goes? The load would most likely be tension, but some compression too.

If you compare 316 Stainless Steel to Zirconia ceramic screws, their tensile strengths are similar (around 75 ksi tensile) with Alumina ceramics being about 1/2 as strong. So you certainly can match the strength of 316 stainless steel with zirconia ceramics in constant compression or tension. However the ceramic screwswill be much more brittle and susceptible to shock so care must be taken in the application.

I need a bolt that can handle high temperatures and be an electric insulator? What can I use?

That depends on what you mean by high temperature and what other issues you have like the strength requirements. If you are talking about temperatures under 500F, then you may consider some engineered polymers. They are non-conductive both electrically and thermally. PEEK is the most economic choice up to about 500F. If you are talking about higher temperatures, then you would have to go with a ceramic like alumina which is an excellent insulatorand resistant to heat well over 2000F

I’m looking for a socket head cap screw that is 5/8″-11 x 5.5 inches in length. Need the material to be non-conductive and was thinking Ceramic Zirconia? Would that work?

Ceramics like Zirconia screws are in fact an excellent insulator from electrical current. However zirconia ceramic fasteners are very limited to smaller sizes between 2 – 1/4″ (M2-M6). Beyond this size they become very difficult to manufacture and are subject cracking. If electrical insulation is what you need, I would suggest a high performance polymer like PEEK socket head cap screws. PEEK is very economical compared to ceramics, an excellent electric insulator and can be made to just about any size. In addition, PEEK is tough, it will not be as fragile as a ceramic while offering the benefits of corrosion resistance and strength.

We are using ceramic screws in one of vacuum furnaces, they’re breaking due to thermal stresses. There is lots of thermal cycling. Are their any less brittle materials we can use?  The environment is low pressure with a max temperature of 1050C. Gases used in the system include: argon, nitrogen, hydrogen and methane.

Since you are dealing with a high temperature, oxygen free environment, the best option would be molybdenum screws. Molybdenum fasteners are ideal for oxygen free vacuums up to 1600C. Molybdenum screws will retain their strength at these temperatures without becoming brittle, expanding or softening. However if there is oxygen in your system molybdenum will fail rapidly at temperatures over 500C, where ceramicswill not.

I’m hoping you can help me with a high temperature issue. I’m running an ammonia plant where gases, along with hot air are heated to temps of 1800-2000F. The secondary reformer unit is made of carbon steel with refractory lining. I need bolting that can survive these temps so I tried Moly but its burning up which I don’t understand because I thought molybdenum was for temps to almost 3000F. Help…

Molybdenum can be used to over 2900F but only in a vacuum where oxygen isn’t present, otherwise it will oxidize quickly. For the temperatures you are dealing with in an air-rich environment, I would suggest Inconel 600 which is usable to 2000F in air or a ceramic like alumina which is usable to 3000F.

What our customers say

More customer feedback
“I purchased from you specifically because of Jon’s expertise and professionalism.”
“Very impressed; good prices and delivered earlier than lead time given, which was a real bonus.”
“Extreme Bolt is definitely on my go-to list.”

Questions?

Our material experts are ready to help guide you through your specific application.