Technical Questions – FAQ’s
Last updated
463 posts · page 14 of 31
Difference Between a DIN 6912 & DIN 912 Socket Head Cap Screw
Q: I have a request for a titanium socket head cap screw. The customer asked to have this screw made to DIN specifications but I found two DIN specs for a socket head cap screw. What is the difference between DIN 6912 and 912? A: A titanium DIN 6912 socket…
Continue readingTitanium Bolts & Galvanic Corrosion in Automobile
Q: I’m using metric Grade 5 titanium bolts, washers and nuts for automotive application. Since the car will never be exposed to any salt water environments do I need to worry about galvanic corrosion? A: Galvanic corrosion is really only a problem if you have a liquid medium between the…
Continue readingInconel 600 or 601 Bolts For High Temperatures?
Q: For a high temperature oxidation-rich environment which would be better Inconel 600 or 601 bolts?A: For this situation it really depends on the temperature range you are dealing with because both an Inconel 600 bolt and an Inconel 601 boltoffer good oxidation resistance. Inconel 600 can service up to…
Continue readingTitanium Gr 5 Bolts vs Super Duplex 2507 Bolts in Brackish Marine Environment
Q: I’m dealing with a brackish marine environment where fresh and salt water combine. I need a strong bolt around 120ksi of tensile strength and have been using Titanium Grade 5, but they are quite expensive. I was wondering if there is a more economic alternative that can handle this…
Continue readingA286 Bolts for Improvement Over Grade 8 in Fuel Application
Q: I’m working with a high temperature waste to fuel application that operates at 1000F normally but could spike to 1200F. Currently I am using Grade 8 bolts but I am concerned about the oxidation resistance of them and their stability at high temperatures. Do you have any material recommendations?…
Continue readingTitanium Gr5 verse Aluminum 7075
Q: How does titanium compare to Aluminum 7075 in terms of strength and density. I need a really strong material with a low strength to weight ratio.A: A titanium bolt will be more dense than an Aluminum 7075 bolt with a density of 4.51 g /cm3 compared to 2.81 g/cc.…
Continue readingTitanium, Monel & Hastelloy for 100% Salt-Saturated Brine Water
Q: I am dealing with near 100% salt saturated brine water @ 195°F. I need material recommendations and price on threaded rod that will survive in that environment. A: Hello, with 100% saturated brine at near boiling temperatures of 195F there are a few materials that can work . Bolts…
Continue readingHastelloy & MR0175
Q: I work on oil rig repair and we are required to have Hastelloy bolts that meet the NACE MR0175 standard. What is this exactly, and do you offer these?A: To answer the easy question, yes we offer Hastelloy screws per NACE MR0175. Now for the my involved question. NACE…
Continue readingPEEK Outgassing for Food Applications
Q: I have a food processing application that requires a polymer screw that can get hot – about 300F. My concern is outgassing in the heat that can contaminate the food chemicals. Is there something that will not outgas that can work for me? A: For your application I would…
Continue readingTitanium Gr5 versus Monel K500 Bolts in Sea Water
Q: I have a subsea application that is exposed to extremely rapid moving salt water. Not only is it faced with these corrosive conditions but it must also be strong – 150 ksi tensile strength – in order to withstand these rough waters and maintain the structure’s integrity. Can you…
Continue readingA286 ASTM F2281 for Temperatures up to 1800°F
Q: I’m a purchasing agent and one of our engineers is requesting a 1/2″-13 x 2″ hex head bolt that is material A286 meeting F2281? What is F2281 mean?A: Good question. F2281is a national standards specification put in place by the ASTM. An A286 bolt that meets the F2281is one…
Continue readingInconel 625 for Oxidation Resistance and Acid Contamination
Q: I have a process that is running at high temperatures that can fluctuate up to 1500F that requires not only oxidation resistance but also some chemical resistance contaminants. I had tried some C276 bolts for the stray acids but they don’t seem to be working mechanically…suggestions? A: A good…
Continue readingNickel 200 Compared to Hastelloy for Caustic Solution
Q: I have a process utilizing a high concentration caustic solution of sodium hydroxide. Would C276 bolts be a good option for corrosion resistance. A: They could be a possibility but you might want to also consider Nickel 200. Nickel 200 bolts find their niche in corrosion resistance to caustic…
Continue reading17-4PH for High Strength Structural Application
Q: We are in the planning process for a structure that must withstand 160 to 165 ksi of tensile strength. Do you have any suggestions on bolting material?A: An ideal bolt for this application would be a 17-4PH bolt. 17-4PH is a material that is over 4 times greater than…
Continue reading17-4PH Screw for Strength Comparable to Grade 8 Steel
Q: Perhaps you can help. I am looking for a stainless-steel substitute to replace a standard SHCS. I will be fastening a stack of hydraulic valves onto a 6061-aluminum manifold with a 3000 PSI working pressure. I am not sure what the tensile strength needs to be comparable to a…
Continue reading
