PEEK Fasteners - Bolts, Screws & Nuts
Last updated
The optimal balance of chemical, mechanical and thermal properties
Need help choosing a material?
In stock
Buy PEEK fasteners onlineScrews, nuts and washers in inch and metric across six head styles, priced by volume and ready to ship. Shop the range.
- Excellent strength, and stiffness up to 500°F (260°C)
- Low coefficient of friction and high wear resistance
- Chemically resistant to common chemicals
- Low out gassing, low particle generation and inherent purity
- Unique physical, thermal & electrical properties
- PEEK fastener styles
- Stock and availability of PEEK fasteners
- Custom injection molded & machined parts
- PEEK material datasheet
PEEK fasteners (chemically known as Polyetheretherketone) offer a unique combination of properties for some of the most extreme applications. PEEK is classified as semicrystalline thermoplastic and high purity polymer, offering excellent mechanical strength and chemical resistance at high temperatures. PEEK fasteners offer a high strength alternative to PTFE fluoropolymers.
Key Benefits
- Excellent resistance to thermal degradation (chemical decomposition caused by heat).
- Chemically resistance to many oils, alcohols, solvents, and organics as well as harsh acids and bases in low concentrations and temperatures.
- Hydrolysis resistance provides PEEK ability to retain all physical properties when continuously exposed to water or steam at high temperatures and pressures, as well as offer very low moisture absorption.
- Outstanding creep resistance allows PEEK fasteners to sustain large stresses over long service life.
- Ability to withstand frequent sterilization processes.
- V-0 flammability rating with low smoke and toxic gas emission when exposed to flame.
- Good wear and abrasion resistance.
- Electrical properties are maintained over a wide frequency and temperature range.
- Radiation resistance allows PEEK to be used in or be repeatedly sterilized by, high doses of ionizing radiation.
Options for High Strength
Depending on the application, PEEK screws can be reinforced with glass or carbon fibers for improved strength and stiffness properties. Reinforced PEEK fasteners offer greater mechanical robustness especially in applications beyond 350°F (175°C).
PEEK 100% / Unfilled
PEEK, with no fillers is unreinforced and 100% polymer. Even without glass or carbon fiber reinforcement, this one of the strongest polymers we offer and well suited for a variety of applications including FDA food contact and other applications requiring high purity.
PEEK Glass Fiber Reinforced
Offers the same chemical resistance as natural PEEK, but also offers increased strength by about 10%. Note, elongation will greatly decrease due to the glass fibers. ***See Note Below.
PEEK Carbon Fiber Reinforced
Provides approximately a 30% increase in strength of pure PEEK. PEEK fasteners with carbon fiber have low elongation and will be electrically conductive. ***See Note Below.
***NOTE: The strength data listed for both PEEK Glass Fiber and PEEK Carbon Fiber fasteners may be significantly less than published values from polymer manufacturers. Normally published data is created from perfect injection molded tensile samples. As most fiber reinforced fasteners are machined from extruded bar stock (not injection molded), fibers are cut when manufactured, sharp angles of fasteners create stress risers, and the orientation of the fibers within the extruded bar are typically perpendicular to the length of the fastener.
As a result, the published values from the polymer manufacturers of these materials are much higher than the ACTUAL values you may expect. The values we have noted on this site are what one might TYPICALLY see in use when the fasteners are machined from bar stock.
Applications
- Viewed by the medical community as an advanced biomaterial, PEEK fasteners are used in medical implants and are compatible with a high-resolution magnetic resonance imaging (MRI).
- PEEK fasteners are one of the few plastics compatible with ultra-high vacuum (UHV) which is necessary for many analytic techniques and particle accelerators.
- Chemical processing and pharmaceutical applications depend on PEEK for it’s chemical resistance, high purity and ability to withstand sterilization processes.
- PEEK fasteners are used in many electronics from cell phones to circuit boards for their lightweight strength and reduced noise, vibration and harshness (NVH).
PEEK Fastener Stock and Availability
Stock
PEEK screws, bolts, nuts and washers are available and ready to ship in many common sizes. You can purchase many of these directly from our online webstore. In addition, we stock other PEEK fasteners. Please contact us for a specific size and part you need.
Custom Availability
PEEK screws and fasteners can be made to order in many different styles and sizes with minimum quantities, typically around 25 pieces. Fasteners can be produced in pure PEEK, glass-filled PEEK, carbon-filled PEEK and PEEK Extreme. We also have the capability to produce unique, per-print custom fasteners. The normal lead time for custom PEEK fasteners about 4 weeks. Be sure to contact us for specific lead times and expediting needs.
- Diameter sizes: Standard #00 – 4” in diameter / Metric M1.2 – M48
- Threads: UNC, UNF
- Minimum Volume – Typically 25pcs depending on size and complexity
- Custom to print
- All DIN / ISO standards
Expediting Options
When time is critical, we can help. When requesting a quote, please let us know your lead time requirements so that we can do our best to accommodate your needs.
| Temperature (°F / °C) | PEEK Unfilled (ksi) | PEEK 30% Glass | PEEK 30% Carbon |
|---|---|---|---|
| 75 / 23 | 14.5 | 16 | 18.8 |
| 260 / 125 | 10.3 | 11.8 | |
| 350 / 175 | 5.4 | 6.2 | |
| 530 / 275 | 3 | 3.2 |
| Property | ASTM or UL test | PEEK Unfilled | PEEK Glass Fiber | PEEK Carbon Fiber |
|---|---|---|---|---|
| PHYSICAL | ||||
| Density (lb/in³) (g/cm³) | D792 | 0.047 (1.31) | 0.054 (1.49) | 0.052 (1.44) |
| Water Absorption, 24 hrs (%) | D570 | 0.1 | 0.1 | 0.4 |
| MECHANICAL | ||||
| Tensile Strength (psi) | D638 | 14,500 | 16,000 | 19,000 |
| Tensile Elongation at Break (%) | D638 | 20 | 2.2 | 1.2 |
| Hardness, Rockwell, R/M Scale | D785 | R126 | R126 | R126 |
| IZOD Impact Notched (ft-lb/in) | D256 | 1.6 | 1.8 | 5 |
| THERMAL | ||||
| Coefficient of Linear Thermal Expansion (x 10-5 in./in./°F) | D696 | 2.6 | 1.2 | 2 |
| Heat Deflection Temp (°F / °C) at 264 psi | D648 | 320 / 160 | 600 / 315 | 660/350 |
| Melting Temp (°F / °C) | D3418 | 644 / 340 | 644 / 340 | 649/342 |
| Max Operating Temp (°F / °C) | - | 480 / 249 | 480 / 249 | 480 / 249 |
| Thermal Conductivity (BTU-in/ft²-hr-°F) | C177 | 1.8 | 3.0 | |
| Flammability Rating | UL94 | V-0 | V-0 | V-0 |
| ELECTRICAL | ||||
| Dielectric Strength (V/mil) short time, 1/8" thick | D149 | 480 | 190 | |
| Dielectric Constant at 1 MHz | D150 | 3.3 | 3.7 | |
| Dissipation Factor at 1 MHz | D150 | 0.003 | - | |
| Volume Resistivity (ohm-cm) at 50% RH | D257 | 1016 | 1016 | 105 |
| APPROVALS | ||||
| Approval | FDA | YES | NO | NO |
| Approval | USDA | YES | NO | NO |
| Approval | NSF | NO | NO | NO |
| Approval | 3A DAIRY | YES | NO | NO |
| Approval | USP CLASS VI | Medical Grades Available | Medical Grades Available | Medical Grades Available |
PEEK fastener styles
PEEK Bolts
PEEK Nuts
PEEK Studs & Threaded Rods
PEEK Washers
PEEK - Frequently Asked Questions
Answers from our engineers, drawn from the PEEK Fasteners - Bolts, Nuts & Screws technical questions we're asked most.
I have a need to replace my current coated stainless steel fasteners with a material that can harmoniously with carbon fiber in a marine application. Do you have a recommendation for this?
With a metal being in contact with carbon fiber in a marine environment you will be susceptible to galvanic corrosion. Ideally if you could isolate the carbon fiber from the metal via a polymer this would be best like PEEK. If your application does not have high strength requirements this might be suitable. If you need a metal, your best bet would be grade 2 titanium. This may not stop the galvanic effects, but it will reduce them. Both of these solutions Extreme Bolt can help you with.
We are looking for a very strong non-conductive M8 socket cap bolt that we can use to mount tooling on the end of a conveyor. There is a lot of leverage and force applied to these brackets and we were shearing off the Nylon bolts. Any suggestions?
One of the strongest non-conductive polymer bolts we could offer would be PEEK. This polymer would be significantly stronger than Nylon. Furthermore there is a reinforced PEEK with glass fiber which may help in your application. The strength of the glass reinforced PEEK is about 10% higher than the standard PEEK screw but it is more brittle so it can fracture more easily.
You could learn more information about this PEEK screws by clicking here.
We are looking to find an electrically non-conductive bolt that would also work at temperatures up to 500 F max. They will be used for an electrically live part isolation kit. Anything that will fit the bill?
Without any understanding of your strength requirements, and focusing solely on the temperature and conductivity requirements, one of the best materials to consider would be PEEK glass reinforced polymer fasteners with glass fibers (for extra strength). PEEK screws are usable to 500F. Also, keep in mind that PEEK glass-reinforced are non-conductive, but carbon-fiber reinforced PEEK will conduct electricity.
Vespel is also another polymer option as it gives you a bit more room on the high side of your temperature requirements, but Vespel screws are VERY expensive and have limited availability in terms of raw material.
I need a flat head screw that is both non-Conductive Fastener and can survive shock and vibration. Any ideas?
Polymers and ceramics are the only options for non-conductive screws. As ceramics are brittle, they would non withstand shock and vibration. In terms of polymers, PEEK is the go-to option for a high strength. PEEK screws are the strongest polymer and will be your best bet to handle shock and vibration.
We are looking for screws to hold down electronic circuit boards. Unfortunately the mounting provisions need to be electrically isolated from the mounts. In addition, we need strength, non-conductivity, and impact resistance, even at cold temperatures (-40C).
A great material to consider would be PEEK screws or PEEK with Glass Fiber reinforcement. These PEEK fasteners are very strong and tough polymers that will be non-conductive. You could learn more information about these fasteners at the following link.
I need a non-conductive screw. Can I use Carbon fiber reinforced PEEK?
NO – The addition of carbon fibers into the polymer will significantly increase the conductivity of the material.
More on PEEK Fasteners - Bolts, Nuts & Screws
What our customers say
More customer feedback“I purchased from you specifically because of Jon’s expertise and professionalism.”
“Very impressed; good prices and delivered earlier than lead time given, which was a real bonus.”
“Extreme Bolt is definitely on my go-to list.”















