Skip to main content
Extreme Bolt & Fastener
Quote

Monel Lap Joint Flanges

Last updated

A Ni-Cu alloy with high strength and good corrosion resistance

Need help choosing a material?

lap joint flange with outline

Strength & Saltwater Resistance

Monel® socket head cap screws are made from a nickel-copper alloy that exhibits high strength, toughness and good corrosion resistance. Renowned for the saltwater corrosion resistance, Monel is the go-to material by the navy. It is often used in many other marine applications for its combination of high strength and seawater resistance. Monel screws are even resistant to rapid moving seawater and will last many years in saltwater conditions.
 
Strength and Toughness from Cryogenic to 1000°F
Monel socket head cap screws offer excellent mechanical properties over a wide temperature range from cryogenic up to 1000°F. In US Navy tear tests at temperatures as low as -320°F, Monel 400 has displayed excellent ductility and toughness. In fact, it has shown little decrease in impact resistance when tested on plates at liquid-hydrogen and liquid-helium temperatures.
 
Monel K500 is an age hardened alloy, known for extreme strength even at high temps. But it is also excellent for cryogenic service. Monel K500's tensile and yield strength increase - with little or no change to ductility and toughness - even at the temperature of liquid hydrogen.
 
Excellent Resistance to Hydrofluoric Acid
One of the most outstanding characteristics of Monel socket head cap screws is that they offer exceptional resistance to hydrofluoric acid (HF), a particularly tough acid to deal with, in all concentrations up to the boiling point. For hydrofluoric acid applications Monel screws are perhaps the most resistant of all commonly used specialty alloys.

The most common grades of Monel flanges are Monel 400 and Monel K500 . Gain more insight on these two nickel alloy grades by accessing our Monel 400 and K500 overviews or by contacting our engineering experts.

Flange Types Available: Blind Flanges, Lap Joint Flanges, Slip On Flanges, Socket Weld Flanges, Threaded Flanges, Weld Neck Flanges


Common Grades of Lap Joint Flanges

Monel 400 

Monel 400, UNS N04400 (QQ-N-281), is a nickel-copper alloy with high strength and excellent corrosion resistance in a range of media including sea water, hydrofluoric acid, sulfuric acid, and alkalies. Monel 400 is commonly in marine engineering, chemical and hydrocarbon processing applications.

Monel 400 Specifications: BS3075NA13 (Wire), BS3076NA13 (Bar), ASTM B 164 (Rod, Bar, and Wire), ASTM B 564 (Forgings), ASME SB 164 (Rod, Bar, and Wire), ASME SB 564 (Forgings), AECMA PrEN 2305 (Wire for Rivets), SAE AMS 4675 (Bars and Forgings), SAE AMS 4730 (Wire), SAE AMS 4731 (Wire and Ribbon), DIN 17752 (Rod and Bar), DIN 17753 (Wire), DIN 17754 (Forgings), VdTÜV 263 (Sheet, Plate, Bar, and Tubing), QQ-N-281 (Plate, Sheet, Strip, Bar, Rod, Wire, and Forgings), Werkstoff 2.4360

Monel 400 — table
Monel 400Ni+CoCuFeMnSiCS
Min %6328.0-----
Max %-34.002.502.000.500.300.024

Monel K500 

Monel K500, UNS N05500 (QQ-N-286),  is a precipitation-hardenable nickel-copper alloy that combines the corrosion resistance of Monel alloy 400 with greater strength (over 2x as strong) and hardness. It also has low permeability and is nonmagnetic to temperatures as low as -150°F (-101°C). 

Monel K500 Specifications: BS3075NA18 (Wire), BS3076NA18 (Rod and Bar), ASTM B 865 (Rod and Bar), DIN 17752 (Rod and Bar), DIN 17753 (Wire), DIN 17754 (Forgings), QQ-N-286 (Rod, Bar, Wire, and Forgings), SAE AMS 4676 (Rod and Bar), ASME Code Case 1192 (Rod and Bar), ISO 9723 (Bar), ISO 9724 (Wire), ISO 9725 (Forgings), Werkstoff 2.4375

Monel K500 — table
Monel K500Ni+CoCuFeMnSiCSAlTi
Min %6327.0-----2.300.35
Max %-33.002.001.500.500.250.0103.150.85

 Mechanical Properties of Monel

Monel 400 elevated-temperature tensile properties: tensile strength, 0.2% offset yield strength, and elongation vs. temperature.

         

Monel K500 — Mechanical Properties
Monel K500Ultimate Tensile StrengthYield Strength at 0.2%Elongation %Usable Temperature Limit
Value160 ksi110 ksi451100°F / 593°C
MONEL 400 - Tensile Data
Temperature
(°F)
Ultimate Tensile
(ksi)
Yield Strength
0.2% Offset
(ksi)
Elongation
%
Room Temp.833245
200793043
400772742
600802746
800682648
1000542440
MONEL K500 - Tensile Data
Temperature
(°F)
Ultimate Tensile
(ksi)
Yield Strength
0.2% Offset
(ksi)
Elongation
%
Room Temp.16011045
20015010847
40014710548
60014210349
80012510219
100095908
PRESSURE – TEMPERATURE RATINGS FOR MONEL 400
Nominal DesignationForgingsCastingsPlates
67Ni 30CuB564 Gr. N04400 (1)...B127 Gr. N04400 (1)
Working Pressures by Classes, psig
Temp., F15030040060090015002500
20 to 1002306008001200180030005000
2002005257001050157526304380
300190490655980147024504080
400180475630945142023653940
500170475630945142023653940
600140475630945142023653940
650125475630945142023653940
700110470625940141023503920
75095465620930139523303880
80080460610915137522903820
85065375505755113018853145
9005027536555082513702285

Monel 400 Corrosion Data

Monel 400 vs nickel alloys — resistance to hydrofluoric acid (20 mil/yr isocorrosion limit, temperature vs HF concentration)

Iso-corrosion diagram for Monel 400 in hydrofluoric acid (HF), showing temperature vs. acid concentration with corrosion-rate contour boundaries for air-free and aerated conditions, plus the atmospheric boiling-point curve.


 Monel Lap Joint Flange Features & Benefits

lap and stud combined

Lap joint flanges are unique in that they are made of two pieces, the flange itself and the stub end.

Flange

  • The backside, has a slight shoulder that is square cut at the center or pipe hole
  • The front side has a flat face with a filleted (rounded) center hole to match the filleted back face of the stub end. Here the stub end will wrap tightly around the center hole of the flange.

Stub End

  • Shaped like a short piece of pipe with a weld bevel on one. This portion of the stub end is also called the sleeve.
  • Narrow shoulder on the flange facing end called is the hub. The back face of the hub has a rounded transition (or inside fillet) that joins the hub to the sleeve

Benefits

  • Economy 
    Because a lap joint flange has a two piece configuration, it offers a way to cut cost when piping systems requires 
  • For high cost alloys the only "wetted" part is the stub end. In this situation, it is only required for the stub-end to be made of the higher cost corrosion-resistant material, where the flange itself can be the produced from lower cost steel.
  • Ease of Work
    By using lap joint flanges, work can be simplified in situations that require frequent and rapid disassemble and assembly during the operation of a plant. The ability to spin that backing flange compensates for misalignment of the bolt holes during assembly.

Questions?

Our material experts are ready to help guide you through your specific application.