Skip to main content
Extreme Bolt & Fastener
Quote

A286 Lap Joint Flanges

Last updated

A Fe-Ni-Cr alloy with excellent high temperature oxidation resistance

Need help choosing a material?

lap joint flange with outline

A286 lap joint flanges are known for their high strength, creep resistance and oxidation resistance at elevated temperatures. This iron-nickel-chromium alloy (once age-hardened) provides A286 lap joint flanges with high levels of strength from room temperature up to about 1300°F (700°C).

A286 lap joint flanges are mildly corrosion resistant. While they should not be used for strong acid environments, they provide excellent oxidation resistance up to 1300°F (700°C) in conditions that would typically be found in high temperature exhaust streams.

Because of these properties, A286 lap joint flanges are often found in high temperature engine, manifold, exhaust and turbine applications as well as off-shore oil & gas applications.

Flange Types Available: Blind Flanges, Lap Joint Flanges, Slip On Flanges, Socket Weld Flanges, Threaded Flanges, Weld Neck Flanges

 


A286 Chemistry, Specifications & Heat Treatments

A286 Heat Treatments:  There are several heat treatment combinations for A286 all with slight variations in performance. They can be specified via an AMS number or a 660 Class: A, B, C or D,  with most common specified as class A or D.   The A286 grades A, B and C all have the same min tensile strength and min yield strength of 130ksi and 85ksi respectively. However grade D is significantly better yield with a min tensile of 130ksi and a min yield of 105ksi. 

By AMS numbers, the most common for A286 is AMS 5737 (same as Grade A) and then AMS 5732 (same as Grade B). 

A286 Specifications: AMS 5525, AMS 5732, AMS 5737, AMS 5804, EN 1.4980, GE B50T1181, GE B50T12, GE B50T81, UNS S66286, Werkstoff 1.4980

A-286 — table
A-286FeNiCrTiMnMoSiCoVaAlCPSB
Min %-24.013.51.91.00.10.003
Max %Bal27.016.02.352.01.51.01.00.50.350.080.0250.0250.01

Mechanical Properties

A-286 tensile curve: tensile strength, 0.2% offset yield strength, and elongation versus temperature.


A286 Lap Joint Flange Features & Benefitslap and stud combined

Lap joint flanges are unique in that they are made of two pieces, the flange itself and the stub end.

Flange

  • The backside, has a slight shoulder that is square cut at the center or pipe hole
  • The front side has a flat face with a filleted (rounded) center hole to match the filleted back face of the stub end. Here the stub end will wrap tightly around the center hole of the flange.

Stub End

  • Shaped like a short piece of pipe with a weld bevel on one. This portion of the stub end is also called the sleeve.
  • Narrow shoulder on the flange facing end called is the hub. The back face of the hub has a rounded transition (or inside fillet) that joins the hub to the sleeve

Benefits

  • Economy 
    Because a lap joint flange has a two piece configuration, it offers a way to cut cost when piping systems requires 
  • For high cost alloys the only "wetted" part is the stub end. In this situation, it is only required for the stub-end to be made of the higher cost corrosion-resistant material, where the flange itself can be the produced from lower cost steel.
  • Ease of Work
    By using lap joint flanges, work can be simplified in situations that require frequent and rapid disassemble and assembly during the operation of a plant. The ability to spin that backing flange compensates for misalignment of the bolt holes during assembly.

Questions?

Our material experts are ready to help guide you through your specific application.