PEEK Pan Head Screws

The optimal balance of chemical, mechanical and thermal properties

• Excellent strength, and stiffness up to 500°F (260°C)
• Low coefficient of friction and high wear resistance
• Chemically resistant to common chemicals
• Low out gassing, low particle generation and inherent purity
• Unique physical, thermal & electrical properties
• Material datasheet for PEEK
• PEEK pan head screw features and benefits

PEEK pan head screws (chemically known as Polyetheretherketone) offer a unique combination of properties for some of the most extreme applications. PEEK is classified as semicrystalline thermoplastic and high purity polymer, offering excellent mechanical strength and chemical resistance at high temperatures. PEEK pan head screws offer a high strength alternative to PTFE fluoropolymers.

Key Benefits

• Excellent resistance to thermal degradation (chemical decomposition caused by heat).
• Chemically resistance to many oils, alcohols, solvents, and organics as well as harsh acids and bases in low concentrations and temperatures.
• Hydrolysis resistance provides PEEK ability to retain all physical properties when continuously exposed to water or steam at high temperatures and pressures, as well as offer very low moisture absorption.
• Outstanding creep resistance allows PEEK screws to sustain large stresses over long service life.
• Ability to withstand frequent sterilization processes.
• V-0 flammability rating with low smoke and toxic gas emission when exposed to flame.
• Good wear and abrasion resistance.
• Electrical properties are maintained over a wide frequency and temperature range.
• Radiation resistance allows PEEK to be used in or be repeatedly sterilized by, high doses of ionizing radiation.

Options for High Strength
Depending on the application, PEEK pan head screws can be reinforced with glass or carbon fibers for improved strength and stiffness properties. Reinforced PEEK pan head screws offer greater mechanical robustness especially in applications beyond 350°F (175°C).

Applications

• Viewed by the medical community as an advanced biomaterial, PEEK pan head screws are used in medical implants and are compatible with a high-resolution magnetic resonance imaging (MRI)
• PEEK screws are one of the few plastics compatible with ultra-high vacuum (UHV) which is necessary for many analytic techniques and particle accelerators.
• Chemical processing and pharmaceutical applications depend on PEEK for it’s chemical resistance, high purity and ability to withstand sterilization processes.
• PEEK pan head screws are used in many electronics from cell phones to circuit boards for their lightweight strength and reduced noise, vibration and harshness (NVH).

Screws made from customer specified PEEK grades are available upon request. See our online store (right side) for common PEEK pan head screws or contact us for specialty or quantity requests.

Screw Types: Flat Head Screws, Hex Cap Screws, Pan Head Screws, Set Screws, Socket Head Cap Screws 

PEEK Pan Head Screw Features and Benefits

Pan head screws are flat on top and rounded on the sides. PEEK pan head screws are ideal for:

• Small diameter fasteners – especially when the fastener size needed is too small for a wrench.
• When phillips or slotted drivers are desired. For many high strength specialty alloys, only slotted drives are available.
• Low torque applications because the drivers don’t offer as much force as a wrench.
• Large diameter head provides more clamping area.

How Are They Different from Button Head Screws?
PEEK pan head and button head screws have very similar profiles however, button head screws allow for a hex socket driver whereas pan head screws do not.

Common PEEK Screw Grades

PEEK 100% / Unfilled

PEEK, with no fillers is unreinforced and 100% polymer. Even without glass or carbon fiber reinforcement, this one of the strongest polymers we offer and well suited for a variety of applications including FDA food contact and other applications requireing high purity. 

PEEK Glass Fiber Reinforced

PEEK 30% Glass Fiber Reinforced provide the same chemical resistance and natural PEEK but nearly doubles in tensile strength.

PEEK Carbon Fiber Reinforced 

PEEK 20% Carbon Fiber Reinforced provides approximately 2.5 times the strength of pure PEEK. 

PEEK Extreme

PEEK Extreme is our proprietary receipe for the highest strength PEEK utilizing carbon fiber reinforcement. This version of PEEK over 3 times stronger than standard unreinforced PEEK. 

 Mechanical Properties of PEEK

 Chemical Resistance of PEEK / Victrex® Screws

PEEK Properties

PEEK Set Screws

The optimal balance of chemical, mechanical and thermal properties

• Excellent strength, and stiffness up to 500°F (260°C)
• Low coefficient of friction and high wear resistance
• Chemically resistant to common chemicals
• Low out gassing, low particle generation and inherent purity
• Unique physical, thermal & electrical properties
• Material datasheet for PEEK
• PEEK set screw features and benefits

PEEK set screws (chemically known as Polyetheretherketone) offer a unique combination of properties for some of the most extreme applications. PEEK is classified as semicrystalline thermoplastic and high purity polymer, offering excellent mechanical strength and chemical resistance at high temperatures. PEEK set screws offer a high strength alternative to PTFE fluoropolymers.

Key Benefits

• Excellent resistance to thermal degradation (chemical decomposition caused by heat).
• Chemically resistance to many oils, alcohols, solvents, and organics as well as harsh acids and bases in low concentrations and temperatures.
• Hydrolysis resistance provides PEEK ability to retain all physical properties when continuously exposed to water or steam at high temperatures and pressures, as well as offer very low moisture absorption.
• Outstanding creep resistance allows PEEK screws to sustain large stresses over long service life.
• Ability to withstand frequent sterilization processes.
• V-0 flammability rating with low smoke and toxic gas emission when exposed to flame.
• Good wear and abrasion resistance.
• Electrical properties are maintained over a wide frequency and temperature range.
• Radiation resistance allows PEEK to be used in or be repeatedly sterilized by, high doses of ionizing radiation.

Options for High Strength
Depending on the application, PEEK set screws can be reinforced with glass or carbon fibers for improved strength and stiffness properties. Reinforced PEEK set screws offer greater mechanical robustness especially in applications beyond 350°F (175°C).

Applications

• Viewed by the medical community as an advanced biomaterial, PEEK set screws are used in medical implants and are compatible with a high-resolution magnetic resonance imaging (MRI)
• PEEK screws are one of the few plastics compatible with ultra-high vacuum (UHV) which is necessary for many analytic techniques and particle accelerators.
• Chemical processing and pharmaceutical applications depend on PEEK for it’s chemical resistance, high purity and ability to withstand sterilization processes.
• PEEK set screws are used in many electronics from cell phones to circuit boards for their lightweight strength and reduced noise, vibration and harshness (NVH).

Set screws made from customer specified PEEK grades are available upon request. 

Screw Types: Flat Head Screws, Hex Cap Screws, Pan Head Screws, Set Screws, Socket Head Cap Screws

PEEK Set Screw Features & Benefits

PEEK set screws are unique in that they have no screw head, meaning that they have no protruding part past the threaded shaft. They are thread only and are available with a socket or slotted driver insert at one end. Set screws are used to secure an object within or against another object. Typically they secure a rotating part such as a gear or shaft. PEEK set screws are driven through a threaded hole in the rotating part until it is tight against the inner object, preventing from moving relative to the outer object. Set screws are available with various points depending on the application.

Cup Point
This is the most commonly used set screw and is identified by a cup-shaped indentation on one end. PEEK cup points are typically used for a quick, semi-permanent or permanent applications where it is acceptable to cut the cup point edge of the screw.

Cone Point
A cone point is easily identifiable by its sharp cone-shaped point – just like an ice cream cone. PEEK cone point set screws deliver the strongest clamping force due to the deep penetration of the point. As a result they are used for permanent assembly.

Flat Point
The cheapest and simplest of the set screw point styles, this screw has a flat surface on the bottom of the screw. This type is used when you need the ability to frequently change parts and require minimal shaft deformation.

Common PEEK Screw Grades

PEEK 100% / Unfilled

PEEK, with no fillers is unreinforced and 100% polymer. Even without glass or carbon fiber reinforcement, this one of the strongest polymers we offer and well suited for a variety of applications including FDA food contact and other applications requireing high purity. 

PEEK Glass Fiber Reinforced

PEEK 30% Glass Fiber Reinforced provide the same chemical resistance and natural PEEK but nearly doubles in tensile strength.

PEEK Carbon Fiber Reinforced 

PEEK 20% Carbon Fiber Reinforced provides approximately 2.5 times the strength of pure PEEK. 

PEEK Extreme

PEEK Extreme is our proprietary receipe for the highest strength PEEK utilizing carbon fiber reinforcement. This version of PEEK over 3 times stronger than standard unreinforced PEEK. 

 Mechanical Properties of PEEK

 Chemical Resistance of PEEK / Victrex® Screws

PEEK Properties

PEEK Fasteners - Bolts, Nuts & Screws

The optimal balance of chemical, mechanical and thermal properties

• Excellent strength, and stiffness up to 500°F (260°C)
• Low coefficient of friction and high wear resistance
• Chemically resistant to common chemicals
• Low out gassing, low particle generation and inherent purity
• Unique physical, thermal & electrical properties
• PEEK fastener styles
• Stock and availability of PEEK fasteners
• Custom injection molded & machined parts
• PEEK material datasheet

PEEK fasteners (chemically known as Polyetheretherketone) offer a unique combination of properties for some of the most extreme applications. PEEK is classified as semicrystalline thermoplastic and high purity polymer, offering excellent mechanical strength and chemical resistance at high temperatures. PEEK fasteners offer a high strength alternative to PTFE fluoropolymers.

Key Benefits

• Excellent resistance to thermal degradation (chemical decomposition caused by heat).
• Chemically resistance to many oils, alcohols, solvents, and organics as well as harsh acids and bases in low concentrations and temperatures.
• Hydrolysis resistance provides PEEK ability to retain all physical properties when continuously exposed to water or steam at high temperatures and pressures, as well as offer very low moisture absorption.
• Outstanding creep resistance allows PEEK fasteners to sustain large stresses over long service life.
• Ability to withstand frequent sterilization processes.
• V-0 flammability rating with low smoke and toxic gas emission when exposed to flame.
• Good wear and abrasion resistance.
• Electrical properties are maintained over a wide frequency and temperature range.
• Radiation resistance allows PEEK to be used in or be repeatedly sterilized by, high doses of ionizing radiation.

Options for High Strength
Depending on the application, PEEK screws can be reinforced with glass or carbon fibers for improved strength and stiffness properties. Reinforced PEEK fasteners offer greater mechanical robustness especially in applications beyond 350°F (175°C).

PEEK 100% / Unfilled
PEEK, with no fillers is unreinforced and 100% polymer. Even without glass or carbon fiber reinforcement, this one of the strongest polymers we offer and well suited for a variety of applications including FDA food contact and other applications requireing high purity.

PEEK Glass Fiber Reinforced
Offers the same chemical resistance and natural PEEK but nearly doubles in tensile strength.

PEEK Carbon Fiber Reinforced
Provides approximately 2.5 times the strength of pure PEEK.

PEEK Extreme
This is our proprietary receipe for the highest strength PEEK utilizing carbon fiber reinforcement. This version of PEEK over 3 times stronger than standard unreinforced PEEK.

Applications

• Viewed by the medical community as an advanced biomaterial, PEEK fasteners are used in medical implants and are compatible with a high-resolution magnetic resonance imaging (MRI).
• PEEK fasteners are one of the few plastics compatible with ultra-high vacuum (UHV) which is necessary for many analytic techniques and particle accelerators.
• Chemical processing and pharmaceutical applications depend on PEEK for it’s chemical resistance, high purity and ability to withstand sterilization processes.
• PEEK fasteners are used in many electronics from cell phones to circuit boards for their lightweight strength and reduced noise, vibration and harshness (NVH).

PEEK Fastener Stock and Availability

Stock
PEEK screws, bolts, nuts and washers are available and ready to ship in many common sizes. You can purchase many of these directly from our online webstore. In addition, we stock other PEEK fasteners. Please contact us for a specific size and part you need.

Custom Availability
PEEK screws and fasteners can be made to order in many different styles and sizes with minimum quantities, typically around 25 pieces. Fasteners can be produced in pure PEEK, glass-filled PEEK, carbon-filled PEEK and PEEK Extreme. We also have the capability to produce unique, per-print custom fasteners. The normal lead time for custom PEEK fasteners about 4 weeks.  Be sure to contact us for specific lead times and expediting needs.
•  Diameter sizes:  Standard #00 – 4” in diameter / Metric M1.2 – M48
•  Threads: UNC, UNF
•  Minimum Volume – Typically 25pcs depending on size and complexity
•  Custom to print
•  All DIN / ISO standards

Expediting Options
When time is critical, we can help. When requesting a quote, please let us know your lead time requirements so that we can do our best to accommodate your needs.

PEEK Fastener Styles

Mechanical Properties of PEEK

Chemical Resistance of PEEK / Victrex® Fastener 

PEEK Properties

PEEK Screws  

Button Head Cap Screws	PEEK button head screws typically feature a socket driver and offer a wide clamping area and low profile. They are best for fastening material that is too thin to counter bore.	• ASME B18.3 • ASME 18.3.4M • DIN 7380 / ISO 7380
Flat Head Screws	PEEK flat head screws are commonly offererd in a 82° countersink angle, but can be custom made to other angles from 60° -120°. Typically PEEK flat heads have a slotted or phillips drive, but can also be custom made with a socket drive. These screws are designed to be flush with the surface.	•  ASME B18.3 •  ASME B18.3.6 •  DIN 963 / ISO 2009 •  DIN 965 / ISO 7046 •  DIN 7991 / ISO 10642
Hex Head Cap Screws	PEEK hex head cap screws feature an added washer face to the bolt head a hex head bolt does not have. Hex head cap screws provide tighter dimensional tolerances over hex bolts. PEEK hex head screws are best for applications that need a high clamping force with easy access. Generally available in #2 - 1/2" sizes and metric sizes.	• ASME B18.6.3 • DIN 931 / ISO 4014 • DIN 933 / ISO 4017 • DIN 961 / ISO 8676
Pan Head Screws	Featuring either a slotted or phillips drive, PEEK pan head screws have a rounded head and are best for small diameter fastener needs, as well as low torque applications.	• ASME B18.6.3 • DIN 7985 • DIN 921 • DIN 85 / ISO 1580 • DIN 84 / ISO 1207   (cheese head) • DIN 966 / ISO 7047   (raised counter sunk)
Set Screws	PEEK set screws are custom made with a cup, cone, flat, dog or half-dog point. Set screws have no head and feature a socket or slotted driver at one end.	• ASME B18.3 • DIN 913 / ISO 4026 • DIN 914 / ISO 4027 • DIN 915 / ISO 4028 • DIN 916 / ISO 4029
Socket Head Cap Screws	PEEK socket head cap screws provide a safe reliable fastener in situations where there is limited access or little clearance around the screws. They are also economic.	• ASMET B18.3 • DIN 912 / ISO 4762 • DIN 7984

PEEK Bolts 

Hex Head Bolts

Similar to hex head cap screws, PEEK bolts do not have the added washer face. They are an economic solution to high clamping force applications with easy access.

• ASME B18.2.1 • DIN 931 / ISO 4014 • DIN 933 / ISO 4017

PEEK Nuts 

Hex Nuts

Most common sizes of PEEK hex nuts are stocked and ready to ship. Custom sizes can also be made upon request.

• ASME B18.16.3 • ASME B18.2.2 • DIN 439 / ISO 4035 • DIN 934 / ISO 4032 • DIN 986

PEEK Studs & Threaded Rod 

Studs	PEEK studs are fully threaded or partially threaded rodsare less than 12" in length. They can be made to any custom length.	• ASME B18.31.2 • DIN 976
Threaded Rod	PEEK threaded rods are available in lengths greater than 1 foot. The minimum order quantity is a total of 6 of rod which can be cut as one- 6ft rod, two-3ft rods, etc.	• ASME B1.1 • DIN 975

PEEK Washers 

Flat Washers

Many sizes of PEEK washers are in stock and ready to ship. PEEK washers are available per SAE, USS, and oversized, as well as custom sizes upon request.

• ASME 18.21.1 • SAE / USS • DIN 125 / ISO 7089 /   ISO 7090 • DIN 126 / ISO 7091