Monthly Archives: April 2017 here

Q: We have a pulp & paper digester that is used to cook wood chips in an alkaline solution. The fasteners will be exposed to high temperatures and abrasive conditions. Any suggestions? A: Without knowing the specifics of your process, I can make two general material suggestions. Duplex 2205 fasteners are … Continue reading

Posted in Application, Corrosion Resistance, FAQs, High Temperature Resistance, Material, Specialty Metal Fasteners, Technical Questions | Tagged , , , , , , , , , , , , , | Leave a comment

Q: I have a robotic application where I need a fastener that is both lightweight and strong. Also, the style of the fastener needs to provide a wide clamping area in a low clearance area. Any suggestions? A: A material you might consider is Titanium, grade 5. The most common … Continue reading

Posted in Application, FAQs, High Strength, Lightweight, Specialty Metal Fasteners, Technical Questions | Tagged , , , , , , , , , | Leave a comment

Q: Is there any advantage of using a Hastelloy B3 fastener over a B2 fastener? A: Both Hastelloy B2 and B3 fasteners provide good resistance to non-oxidizing acids, such as hydrochloric acid and sulfuric acid. The only advantages of Hastelloy B3 fasteners over B2, is that they offer enhanced thermal stability … Continue reading

Posted in Application, Corrosion Resistance, FAQs, Material, Specialty Metal Fasteners, Technical Questions | Tagged , , , , , , , , , , | Leave a comment

Q: I saw on your high temperature chart that Molybdenum is listed twice. I’m confused, which high temperature should I use? A: Both high temperatures are accurate, depending on the situation where you are using Molybdenum fasteners. Molybdenum screws can be used up to 2912F only if it is used … Continue reading

Posted in FAQs, High Temperature Resistance, Specialty Metal Fasteners, Technical Questions | Tagged , , , | Leave a comment

Q: What is the difference between Incoloy 825 and 925 bolts? A: Bolts made from Incoloy 925 are precipitation hardened version of Incoloy 825 bolts. What this means is it is put through a heat treatment process which hardens the alloy at the atomic level. Basically Incoloy 925 bolts offers similar … Continue reading

Posted in FAQs, High Temperature Resistance, Specialty Metal Fasteners, Technical Questions | Tagged , , | Leave a comment

Q: I’m currently using Monel 400 hex head bolts in salt water. Should I be using K500? What’s the difference? A: Basically, Monel K500 is a precipitation hardened version of Monel 400. This means the material goes through a heat treating process that changes the alloy’s structural matrix to increase its tensile and … Continue reading

Posted in Corrosion Resistance, FAQs, Specialty Metal Fasteners, Technical Questions | Tagged , , , , , | Leave a comment

Q: How does creep occur and what polymer is best to prevent this? A: Creep is the permanent deformation of the material caused by constant load or stress, usually accompanied by constant high temperature. This can result in permanent changes of the fastener shape as well weakening and fracturing of the … Continue reading

Posted in Engineered Polymer Fasteners, FAQs, High Strength, Technical Questions | Tagged , , | Leave a comment

Q: I have a seawater application where the water can be stagnant or polluted. Is Monel bolts the best choice? A: For stagnant seawater application we would usually suggest Titanium over Monel fasteners. Although Monel is very resistant to saltwater, it can experience pitting corrosion in stagnant water situations. There have … Continue reading

Posted in Corrosion Resistance, FAQs, Specialty Metal Fasteners, Technical Questions | Tagged , , , | Leave a comment

Q: What is the highest temperature I could use Inconel 718 bolts? A: Inconel 718 fasteners could be used reliably up to about 1300F.  Because Inconel 718 is  heat treated or age hardened at 1325F, going beyond 1300F will significantly affect its strength properties. Furthermore, its strength may not fully return. … Continue reading

Posted in FAQs, High Strength, High Temperature Resistance, Specialty Metal Fasteners, Technical Questions | Tagged , | Leave a comment